Nothing can be more unpleasant than waking up in the middle of the night with a cold. If your furnace isn’t operating properly or at all, it may become a complicated situation. You can troubleshoot and fix your furnace yourself if you have some DIY knowledge. However, in some instances, it is mandatory to call experts offering furnace repair near you.
To avoid the problem, have a maintenance checklist for your heating system handy. Before going ahead and calling your local experts, figure out if you are facing any of the problems mentioned below:
If you are facing any or all of the problems mentioned above, don’t worry. You’re not alone. Here we have some remedies of what you can do to get rid of these malfunctions.
We understand how absurd this sounds. If you’ve been jolted awake by the cold, double-check that your heater is set to “hot” and that the setting selected is at least five to six degrees higher than your room temperature. This is one of the common mistakes most people make. They forget to verify if they had switched their furnace “on.” Make sure you do the following:
Check to see whether your furnace filter needs to be replaced.
Filter failures are arguably one of the most prevalent furnace issues, owing to homeowners’ forgetfulness about the filters. Filters purify the air that enters the furnace and the heated air that is returned to the home. A blocked or filthy filter restricts airflow, causing heat and pressure to build up in the furnace.
Newer, more effective furnaces are more sensitive to the problem and will frequently stop down before a clogged filter does further damage. The furnace will continue to function in other aspects but with decreased heat production and efficiency.
First, look for visible dirt in your filter. Cleaning and reusing inexpensive hardware-store filters is not a good idea. They’ve been treated with a dirt-catching oil, and once saturated, they lose their effectiveness. Homeowners should change their filters once a month. It will be a lot simpler to remember a monthly habit than every two months—and it is that vital.
Another method to tell if your filter is failing is to check for a whistling sound. If the furnace is unable to obtain enough air through the filter, it will suck air via any available hole. A whistling sound indicates that there is a problem.
Some thermostats are hardwired into the home’s electrical system, while others are powered by batteries. What is the source of electricity for your device? When a battery has to be replaced, certain devices will flash a low-battery indication, although most homeowners commonly ignore the warning.
Check the circuit breaker if the machine does not turn on. Still haven’t figured out what’s wrong? The following is the next stage in the furnace troubleshooting process:
Check if it’s in the “Off” position or whether it’s stuck in the middle since your circuit breaker tripped. The switch is red in certain panels. Some technicians do a poor job of marking — or appropriately identifying — household electronic appliances. You must search for the switch that is not located in the same place as the others on the furnace. To solve the power issue, turn the circuit completely off and then our it back on.
Furnaces built after 1990 feature a small window through which light is displayed. The light cannot only inform you if the furnace is on, but it could also flash a code to let you know what’s wrong. Note the sequence of the flashing light if you’ve turned the furnace off and back on. Then remove the access panels from the furnace (there are usually two). There will be a key within each one that will tell you what the code means. If the furnace still doesn’t start after you replace the panels, a technician would be able to figure out a remedy.
Please don’t try a “do-it-yourself” repair if you don’t understand the underlying problem. If your furnace isn’t operating properly or has just stopped operating, you should seek the help of certified specialists.
It’s not only that specialists can work more quickly and precisely. It’s also because of their diagnostic capabilities. If your gas furnace makes a constant clicking noise, it might signal several issues, including electrical issues, a jammed gas valve, faulty ignition, or a fractured heat exchanger.
A specialist knows how to identify the root of the problem and then resolve it. Sometimes all it takes is a single precise, focused repair to keep your furnace running well for another couple of years.
Yes, this may be the most drastic approach to resolving furnace issues. However, in many cases, this is the greatest remedy for a furnace that has become bothersome and inefficient. This is, without a doubt, the most effective long-term remedy for furnace issues. But when is it appropriate to choose this path? It is determined by several factors, including the age of the furnace. A gas furnace may last up to 20 years; once it reaches that age, it’s usually preferable to replace it.
If you are looking for companies offering furnace repair services in Santa Rosa, but don’t know where to start, we got your back. Call John Owens Services at 707-207-8592.
Our philosophy is simple, we always want to maintain equipment to give it the longest life possible. Next, we want to focus on repairing when something goes wrong. Then only as the last choice, we replace equipment when needed. That’s the John Owens Way.
San Rafael 
Book Now